600cc And 700cc Smarts
You don't have to remove the front panel but it helps. This How2 can be found here.
Remove the top cover by undoing the 3 Torx screws.
The centre screw is Torx25 and the outer screws are Torx30.
Pull the plastic cover directly upwards to remove it from the car.
This adjuster moves the headlight reflector left and right using a 6mm hexagon key (allen key).
This adjuster moves the headlight reflector up and down using a 6mm hexagon key (allen key).
When replacing the cover, ensure it's sitting behind the headlight tabs.
Thanks to BlackDog for the picture below.
This shows that it is possible to adjust the headlights through the service screens without removing the front panels. The space is a bit tight so don't drop the allen key, tie string around it just in case.
It may turn out to be a lot easier if you have a flexidrive screwdriver and a 6mm bit.
451 999cc Smart Fortwo
Gain access to the headlights by opening the bonnet.
Look on the top of each light and you will see 2 adjustment screws (circled below).
The adjuster near the middle of the car (circled red below) adjusts the main beam up and down.
The adjuster near the side of the car (circled green below) adjusts the dipped beam up and down.
With the headlight removed there's a pentagon socket for adjusting the dipped beam left and right.
You shouldn't need to adjust left and right, up and down should do the job perfectly.
Because of the tight space, it can be easier to remove the light units so you can fine
tune the adjustment. Put the light unit in place to check before screwing it back down.
The back of the light units have three 7mm adjustment bolts.
Bolt 1 adjusts the up and down of the beam.
Bolt 2 adjusts the left and right of the beam.
Bolt 3 is not usually needed, it is the pivot point for the other two bolts.
Adjust bolt 2 and 3 so they have the same gap between the light and the holder.
This will allow the light to shine directly straight forwards.
Now adjust bolt 1 to move the light up or down to the correct level stated below.
Repeat on the other side so both lines are level.
How Do I Know If/When My Lights Are Correctly Aligned?
Without the correct equipment it's impossible to be 100% accurate but
a good guess is better than illuminating the moon or on coming traffic.
Pull up close to a wall or fence. Use a marker or a bit of tape to make 2 X's.
These X's should be directly in front of the dipped beam bulbs.
Pull the back away from the wall so the headlights are 5 meters away from the X's.
Using the adjusters on the headlights, move the projected light so the cut off line is 5cm below the centre of the X. That is the vertical alignment sorted.
Each light beam will have an up-turn that travels up and off to the left (on RHD cars).
This up-turn needs to start about the same distance from the X on both sides.
That is the horizontal alignment sorted.
As I said earlier, it isn't perfect but it's better than nothing.
Ideally you need to go to an MOT station and get them to use their beam setter.
451 Smart Light Output
The new smart (451) uses projector lights like the Roadster, these offer superior light output.
One thing that is different is the beam shape. The twin upturns seen on the fortwo and Roadster
have now been replaced with a Z-line light cut off shape. This shape is shown below.
The new shape allows extra lighting of the road side but reduces glare to people you are overtaking.
If you have your dipped beams turned on and you don't get a nice pair of cut off lines
and all you get is the shape below for one or both lights...
...it means that you have wired your full beams to the dipped beams.
Swap the top and bottom pair of connectors and try again.
My Upturns Travel In The Other Direction
That's because you have left hand drive headlights.
My Head Lights Won't Adjust Far Enough
It's a fairly rare occurrence but it has been known for the reflector to unclip itself from the adjuster
so it's either wildly out of adjustment, won't pull in far enough or alignment changes itself.
The only way to remedy this is to remove the headlight and take it apart.
Once apart you should be able to see which clip isn't attached.
A quick push on the reflector will reseat the clip and the correct adjustment can be made.
I Can't See A Distinct Cut Off Line
There is a technical name for this, it's called 'crap bulbs'.
Poorly made bulbs do not create a crisp clear lighting pattern because of excessive
glare. Auto Express magazine did a test on bulbs and the results were shocking.
Amongst the poor performers were:
Bosch Xenon Power
Ring Ultra Xenon
GE Megalight Plus
PIAA Platinum White
Ring Ice Blue
Halfords Laser Blue
So it goes to show that costly bulbs from known brands don't necessasarily mean quality.
The best bulbs tested were as follows:
Halfords Super Brilliance
Philips Power2Night GT150
Osram Cool Blue
Philips Blue Vision
So What Are The Best Bulbs To Get?
Well, none of the above really. PIAA bulbs can be good (except for the platinum white) but expensive, HIDs give good output but are expensive or poor quality and illegal.
At the moment, the best bulbs to get are Osram Nightbreakers and Philips X-treme Power.
Philips X-treme retail at £25 a pair. Osram Nightbreakers are cheaper at about £15.
For a beam of light to be placed at a particular point it has to hit the reflector at
the correct angle. The filament inside the bulb has to be positioned within a fraction
of a millimetre to create the perfect beam pattern. If the bulb is badly manufactured
or the bulb isn't installed very well, it can throw the beam off. It is the poor placement
of the filament that causes glare and the poor cut off line.
One of the main dimensions for an H7 bulb is the distance from the top of the base to the
bottom of the filament. This distance should be 25mm (+ or - 0.2mm). If you have a poor
cut off line, check the bulb by measuring this dimension (don't touch the glass).
How Do I Know If I Have Good Bulbs?
As said before, you should get a fairly crisp cut off line but there is one more thing to look for.
Check out the quality of the up-turns in the dark and up against a smooth surface.
A sign of a good bulb is that the up-turns aren't solid light but actually have lines running through them perpendicular to the up-turns top line. This is actually the magnification of the bulbs filament.
Look closely at the upturn and you can actually see the coil of the bulb.
By printing this document I state I have read and understood this disclaimer